Focused arrival windows
Useful updates and clear arrival timing.
Standing seam metal is the premium pitched roof in Houston, and it is growing on new custom builds in Memorial, River Oaks, and Tanglewood. It sheds rain, holds up to wind, and lasts far longer than shingles, but it is only as good as its seams, its flashing, and its fastening. Metal roofing in Houston means naming the system before naming a price. Start with a roof inspection and a written scope.
Useful updates and clear arrival timing.
Review the approach and price before deciding.
Equipped vehicles and respectful cleanup.
Neighbors serving neighbors with follow-through.
A metal roof is a system: panels, seams, clips, flashing, underlayment, and ventilation. Here is what is part of the job.
Concealed fasteners, raised seams, and clips that let the panels move with heat. The standing seam roof Houston custom builds carry most.
Steel panels with a stone-chip coating, shaped like shingle or tile. The premium pitched alternative where the look of shingle or tile is wanted with steel underneath.
Underlayment across the field, with a self-adhering membrane at valleys, eaves, and around penetrations.
Chimney flashing, vent flashing, and drip edge are replaced, not reused. On a metal roof, flashing is where most leaks start.
Clips, fasteners, and edge details are suited to the wind exposure of the house. Wind uplift is a topic on every metal scope.
Ridge vent paired with soffit intake. A metal roof still needs the attic to breathe.
Tell us the house, the slope, and what the roof is doing. We will talk through the next step and what an inspection covers.
Metal roofing in Houston is standing seam and stone-coated steel, installed as a system. The panels are the visible layer. The clips, seams, flashing, underlayment, and ventilation underneath them are what decide whether the roof holds through hurricane season.
Standing seam metal in Texas runs $8 to $22 per sq ft of roof surface across published sources, a wide spread driven by gauge, finish, and panel system. Angi Houston puts a metal roof at about $10,995 on average, and about $11 per sq ft for common coated steel. The page must name the system before naming a price, and these are published market ranges, not this business's prices. Your price depends on the system, the gauge, the finish, and the roof, and is set out in a written scope after an inspection.
The market is the custom build. Standing seam and stone-coated steel are growing on new custom builds in Memorial, River Oaks, and Tanglewood, and on modern infill in the Heights and Montrose. The roofs are steep, complex, and visible, which is why the flashing and seam work matters more than the panel brand.

We walk the roof, check seams, clips, flashing, and penetrations, and photograph what we find. You get a written scope with the system, the gauge, and the work included.
Standing seam or stone-coated steel, chosen for the house, the slope, and the look. The system is named before any price is discussed.
A re-roof inside the city needs a City of Houston Residential Roofing Permit, about 10 business days. The permit is part of the written scope.
Old material comes off to the deck, soft sheathing is replaced, and the new system goes on: underlayment, membrane, flashing, clips, and panels.
We walk the roof and the yard with you and hand over the photos of the deck, seams, and flashing details for your records.

Folds standing seam panels together so the seam is weather-tight.
Cut panels cleanly at valleys, hips, and penetrations.
Checks the deck and attic for hidden moisture before new panels go on.
Keep panel courses straight and cut clean edges.
Picks up fasteners and offcuts from the yard and driveway.
Safe access and staging across steep roof planes.
Seals flashing joints and penetrations as part of the work.
Every panel, valley, and flashing bend is measured to the roof in front of us.
Landscaping and the driveway are covered before tear-off starts.
Photos of the deck, seams, and finished roof go into your file.

The owners wanted a roof that would hold through hurricane season and outlast the shingles around it. We installed a standing seam system with clips suited to the wind exposure and new flashing throughout.
Flashing at a chimney had failed and water was tracking under the panels. We replaced the flashing, re-seated the panels, and photographed the work for the file.
The owners wanted the look of shingle with steel underneath. We installed stone-coated steel panels with new flashing and balanced ventilation.
Metal is the premium pitched roof, and its streets are the custom-build streets: Memorial, River Oaks, Tanglewood, and modern infill in the Heights and Montrose. The roofs are steep and complex, and the flashing work matters more than the panel choice. Wind uplift is the topic on every metal scope, because a metal roof that lifts at the edge fails fast. Call (936) 873-7200 to talk through a metal roof.
New custom builds and mid-century restorations carry standing seam metal and flat TPO, often on the same house.
Slate, clay tile, copper, and standing seam metal, with property owners association review before any material or colour change.
Custom builds on large lots, where metal is the premium pitched alternative to shingles.
Standing seam metal on modern infill, beside 1920s bungalows with shingle roofs.
Metal on modern infill townhomes, with flat TPO decks and rooftop terraces alongside.
clips, fasteners, and edge details are suited to the wind exposure of the house.
the season runs 1 June to 30 November, peaking in the second week of September. We document wind damage with photos.
A new custom build that needed a roof to hold through hurricane season and outlast the shingles around it.
We installed a standing seam system with clips suited to the wind exposure and new flashing throughout.
Maintenance: Walk the roof after any tropical storm. Check seams and flashing at the edges first.
Flashing at a chimney had failed and water was tracking under the panels.
We replaced the flashing, re-seated the panels, and photographed the work for the file.
Maintenance: Check flashing at chimneys and penetrations each year. On a metal roof, flashing is the leak point.
Owners who wanted the look of shingle with steel underneath on a modern infill home.
We installed stone-coated steel panels with new flashing and balanced ventilation.
Maintenance: Keep valleys and gutters clear. Debris holds water against any roof, metal included.
Metal roof problems in Houston trace back to seams, flashing, and fastening. Here is what we fix.
On a metal roof, most leaks start at chimney flashing, vent boots, and panel transitions, not at the panels. We replace flashing and re-seat panels where the roof has life left.
Wind works on the edges and corners of a metal roof first. We check clips, fasteners, and edge details on every inspection and say what we find.
Houston heat shortens shingle life to roughly 18 to 25 years. A metal roof is the premium alternative for owners who want a longer-lived pitched roof.
Stone-coated steel gives the look of shingle or tile with steel underneath, for houses where the streetscape matters.

Our crews install metal roofs across Harris County every week, from custom builds in Memorial to modern infill in the Heights. Every install is photographed at the deck, seam, and flashing stages, and the permit inspection is part of the job. That is what a homeowner can actually check: the photos, the permit, and the written scope.

“We contacted Thomas Family Roofing for an estimate on repairs for our metal roof in Houston. Luis came out, inspected the roof in person, and explained clearly what needed attention, including a few details about flashing and panel areas that other roofers had missed.”
“From our first call with Thomas Family Roofing, it was clear they were focused on giving us a quality new roof and making the whole roofing process easy to understand.”
“They replaced an old cracked skylight on the roof of my two-story home, and I was very pleased with the whole roofing process. From the first call back to the roof inspection, estimate, and final installation, everything was handled on time.”
Rating 4.9 out of 5 from 46 Google reviews (42 five-star, 4 four-star). A further 41 reviews are visible only as an aggregate on Google. See all reviews on Google.
Standing seam metal in Texas runs $8 to $22 per sq ft of roof surface across published sources, driven by gauge, finish, and panel system. Angi Houston puts a metal roof at about $10,995 on average. These are published market ranges, not this business's prices.
Texas sources put metal roof life at 40 to 70 years, against roughly 18 to 25 years for architectural shingles in Houston. The seams, flashing, and fastening decide whether the roof reaches that life.
They suit different houses. Standing seam has concealed fasteners and raised seams. Stone-coated steel is shaped like shingle or tile. The choice is made for the house, the slope, and the look, and written into the scope.
A City of Houston Residential Roofing Permit is required for a re-roof or overlay inside the city — plan review and inspection, a $33.56 admin fee, about 10 business days, valid 6 months. Roof covering of 100 sq ft or less in aggregate is exempt. In unincorporated Harris County there is no residential roofing permit.
Not seeing your question? Call (936) 873-7200 and talk it through with the local team.
Ask the local teamCall (936) 873-7200 and tell us what you are seeing. We will talk through what is happening, what an inspection covers, and the next step. Or send a service request with the form and we will call you back.